Chimney relining in Milford, Connecticut is the permanent fix for a cracked, rusted, or missing flue liner. If your fireplace smokes back, your masonry shows creosote stains, or a sweep flagged a damaged chimney liner, we install a stainless steel chimney liner Milford homeowners trust. We serve Woodmont, Devon, Walnut Beach, and every neighborhood in between.
Chimney relining in Milford, Connecticut means installing a new flue liner inside your existing chimney so exhaust gases, sparks, and heat never touch the brick. We run a stainless steel chimney liner from the top of the flue down to the smoke chamber, insulate it, and connect it to your appliance or fireplace. A proper job also includes a smoke test kit check, a new chimney cap, and a damper clamp if you burn gas logs.
Milford's older housing stock takes a beating. Salt air off Long Island Sound eats at mortar joints, and freeze-thaw cycles crack chimney crowns from November through March. That lets water in, which rusts clay tile liners and spalls brick. If you have been searching for chimney relining near me Milford CT because your flue is failing, we can usually inspect and quote the same week. Most liner replacements in this area run $2,400 to $6,800 depending on height and liner size.
Every reline is a complete system, not just a pipe dropped down the flue. The list below covers what comes standard on a Wire Neo job. If your chimney needs crown, flashing, or masonry work beyond this, we quote it separately before we start so there are no surprises.
We run an inspection camera the full length of the flue and photograph the smoke chamber, damper, and crown. You see the footage and get a written summary of what we found and what it means.
A chimney brush and rods clear creosote and debris before installation. We grind or chip jagged tile edges smooth so they cannot tear the new liner as it goes down.
We install a stainless steel chimney liner sized to your appliance, wrapped in insulation rated for the flue. Brands include DuraVent and Selkirk, both UL-listed for wood, gas, and oil applications.
The liner gets a top plate and a stainless cap with spark screen. We seal the termination against water and secure it for coastal wind, which matters on chimneys near the Sound.
We parge the smoke chamber with refractory mortar to smooth the transition from firebox to liner. This improves draft and removes ledges where creosote can collect.
Before we leave, we run a smoke test kit check to confirm draft and look for leaks at every joint. Then we walk you through the install and schedule your first annual sweeping.
We run an inspection camera down the flue and check the smoke chamber, damper, crown, and flashing. You see the footage. If the clay tile is cracked or missing, we document it and measure the flue's inside dimensions for sizing.
We match liner diameter to your appliance, not to the old flue. A wood fireplace needs a different size than a gas insert or oil furnace. You get a flat quote covering the liner, insulation, cap, and any masonry work needed at the top.
Before anything goes in, we sweep the flue with a chimney brush and rods, then grind or chip away jagged tile edges that could tear the liner. Drop cloths cover the hearth and floor. Most prep takes one to two hours.
We pull the stainless steel liner down from the roof, wrap it in insulation, and set it with a top plate and cap. A masonry trowel and refractory mortar seal the smoke chamber and any gaps at the crown. This is the longest step, usually three to five hours.
We build a small fire or use a smoke test kit to confirm draft and check every joint for leaks. Then we walk you through what we installed, how to operate the damper, and when to schedule the next sweeping.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
We run it the full length of the flue to find cracks, gaps, and obstructions before quoting. You see the same footage we do, which takes the guesswork out of the recommendation.
Standard sweeping tools for removing creosote and debris before installation. A clean flue lets the liner slide down without snagging and gives the insulation a clean surface.
We use it to smooth jagged tile edges and cut back obstructions inside the flue. Sharp edges can tear a liner during the pull, so this step matters more than it sounds.
Mixes refractory mortar for smoke chamber parging and crown repairs. Consistent mortar consistency is what makes the parge hold up to heat cycling.
Confirms draft and checks every joint for leaks before we call the job done. If smoke escapes anywhere it should not, we find it and fix it on the spot.
Required when gas logs are installed, so the damper cannot be fully closed. It keeps carbon monoxide from backing into the room if the gas appliance is running.
A 1952 cape near the water had three cracked tiles and a rusted damper. The homeowner smelled smoke in the upstairs bedroom whenever the fireplace was lit. A previous sweep had recommended a full rebuild.
We installed a 6-inch insulated stainless liner, replaced the damper, and added a stainless cap. The smoke smell stopped on the first fire. Total job took one day and cost roughly a third of the rebuild quote.
The fireplace smoked into the living room on every burn. The flue was 12 by 12 inches, far too large for the fireplace opening, so it never warmed up enough to draft. Two winters of use had left creosote stains on the brick.
We sized and installed a 6-inch stainless liner with insulation, parged the smoke chamber, and added a top plate and cap. Draft was correct on the first test fire. No smoke in the room since.
Water was showing up in the firebox after every storm. The crown had a visible crack and the flashing had pulled away from the roof. The clay liner had rust stains running down its full length.
We repaired the crown with crown sealant, replaced the flashing, and installed a stainless liner because the tile was already compromised. A water test after the job showed no leaks. The homeowner has had two dry seasons since.
Most reline calls come down to one of these four issues. Each one gets worse if you wait, and each one has a straightforward fix once we get a camera in the flue.
Ask a pro →We install a stainless steel liner inside the existing flue, which restores the barrier between exhaust and structure. The old tile stays in place as a backer. Most jobs finish in one day and pass inspection on the first pass.
We measure the appliance's BTU output and size the liner to match. A correctly sized, insulated liner stays warmer and drafts reliably. Customers notice the difference on the first fire, with no smoke rolling into the room.
We find the entry point with a water test, repair the crown or flashing, then reline the flue if the tile has already been damaged. Crown sealant and ChimneySaver water repellent finish the job so water stays out.
When the tile is too far gone for sweeping, relining is the answer. The new stainless liner gives creosote a smooth surface that sweeps clean each year. We also install a cap and schedule annual maintenance so it stays that way.
Most chimney relining jobs in Milford run $2,400 to $6,800 in 2026. A single-story interior flue with a 6-inch liner sits near the low end. Tall exterior chimneys, oversized flues, or jobs that need crown and flashing repair push toward the top. We quote the liner, insulation, cap, and any masonry work as separate line items so you can see exactly where the money goes.
A standard chimney liner installation takes one day, usually five to eight hours on site. Prep and sweeping run one to two hours, the liner pull and insulation wrap take three to five, and the smoke test and cleanup add another hour. Two-story exterior chimneys or flues with heavy tile damage can stretch into a second day.
You need one if your clay tile liner is cracked, missing, or too large for your appliance. You also need one if you switched from wood to a gas insert or oil furnace, because those appliances run cooler and produce acidic exhaust that eats clay tile. A camera inspection tells us for sure. If the existing tile is intact and correctly sized, we will tell you so.
Wire Neo relines chimneys across Milford, from Downtown and Milford Center to Devon, Woodmont, and the Boston Post Road corridor. We are CSIA-certified, licensed in Connecticut, and have been working in this area since 2021. Call (844) 796-3584 and we will schedule an inspection, usually within the same week.
Chimney Repair Near MeGeneral chimney repair covers the masonry, crown, and flashing issues we often find during a reline. If your chimney leaks or has loose brick, we fix that before or alongside the liner so the whole assembly is sound.Explore →
Chimney Masonry RepairCracked firebrick and deteriorated mortar joints let heat and moisture into the chimney structure. We repair masonry with refractory mortar and tuckpointing before installing a new liner, so the liner has solid material to sit against.Explore →Chimney Crown RepairA cracked crown is the number one cause of water in the flue. We seal or rebuild crowns with crown sealant and pair it with relining so water stops running down the inside of your chimney.Explore →
Chimney Cap RepairThe cap keeps rain, birds, and debris out of the flue. Every reline we do includes a new cap or a cap repair, because an open flue top undoes the protection the liner provides.Explore →
Chimney MaintenanceAnnual sweeping and inspection keep a new liner working. We schedule maintenance visits for Milford customers and check the liner, cap, crown, and flashing each time so small problems get caught early.Explore →
Fireplace RepairDamper issues, cracked firebox panels, and smoke chamber problems often show up at the same time as a failing liner. We repair the fireplace box and parge the smoke chamber as part of a complete reline.Explore →
Emergency Chimney RepairAfter a chimney fire or a storm that knocks flashing loose, you need someone fast. We handle emergency calls in Milford and can often tarp or stabilize the chimney the same day.Explore →
24/7 Chimney RepairChimney problems do not wait for business hours. Our 24/7 line takes calls for active leaks, smoke backdraft, and post-fire inspections so you are not stuck waiting until Monday.Explore →If your flue is cracked, your fireplace smokes, or a sweep flagged a damaged liner, do not wait for the next burn season. We inspect, quote, and reline with UL-listed stainless steel. Call (844) 796-3584 and we will get you on the calendar this week.
Book Inspection (844) 796-3584 →Call (844) 796-3584 or send us a message and we will get back to you the same day. Our phone line stays open 24/7 for emergencies, and regular estimates get scheduled within a day or two. Tell us what you are seeing, hearing, or smelling and we will tell you what it likely means before we even get on the roof.